View CXL5001M_143973.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CXL5001M/P
CMOS-CCD 1H Delay Line for NTSC
Description The CXL5001M/P are general-purpose CMOS-CCD delay line ICs that provide 1H delay time for NTSC. Features * Low power consumtion 80mW (Typ.) * Small size package (8-pin SOP, DIP) * Low differential gain DG = 3% (Typ.) * Input signal ampiitude 180 IRE (= 1.28Vp-p, Max.) * Low input clock amplitude operation 150mVp-p (Min.) * Built-in peripheral circuits (clock driver, timing generator, autobias, and output circuits) Functions * 680-bit CCD register * Clock drivers * Autobias circuit * Sync tip clamp circuit * Sample and hold circuit Structure CMOS-CCD Absolute Maximum Ratings (Ta = 25C) * Supply voltage VDD 11 V * Supply voltage VCL 6 V * Operating temperature Topr -10 to +60 C * Storage temperature Tstg -55 to +150 C * Allowable power dissipation PD CXL5001M 350 mW CXL5001P 480 mW Recommended Operating Conditions Supply voltage VDD 9 5% V VCL 5 5% V Recommended Clock Conditions * Input clock amplitude VCLK 150mVp-p to 1.0Vp-p (250mVp-p typ.) * Clock frequency fCLK 10.7MHz
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
CXL5001M 8 pin SOP (Plastic)
CXL5001P 8 pin DIP (Plastic)
-1-
E50799A78-PS
CXL5001M/P
Blook Diagram
AUTO FEED OUT
5 ref. (1 BIT) CLAMP CIRCUIT 680-BIT SHIFT REGISTER 1 2 AMP S/H 1 AMP 2 AMP 4
IN
8
7
6
AUTOBIAS CIRCUIT
CLOCK DRIVERS
DUTY CONTROL CIRCUIT
1
2
3
VSS
VCL
Pin Description Pin No. Symbol 1 2 3 4 VSS VCK CLK VDD Description GND 5V power supply Clock input 9V power supply > 100k Impedance [] Pin No. Symbol 5 6 7 8 OUT FEED Description Signal output Impedance [] 600 to 1k
CLK
Feedback DC output > 100k 10k > 100k
AUTO Autobias DC output IN Signal input
-2-
VDD
CXL5001M/P
Electrical Characteristics (Ta = 25C, VDD = 9.0V, VCL = 5.0V, fCLK = 10.7MHz, VCLK = 250mVp-p sine wave, See "Electrical characteristics measuring circuit") Item Symbol IDD ICL Measuring condition 250kHz, 1.28Vp-p, sine wave input 250kHz, 1.28Vp-p, sine wave input IG = 20 log (Output voltage [Vp-p] / 1.28 [Vp-p]) Dissipation at 3.5MHz in relation to 250kHz fG = 20 log (V3.58MHz/ V250kHz) (Note 1) 5-staircase wave input Y = 140 IRE (=1.0Vp-p) Measure S point with vector scope (Note 2) SW conditions Measuring point 1 2 a a A1 A2 Min. -- -- Typ. Max. Unit 4 9 5 11 mA mA
Supply current
Insertion gain
IG
a
a
V1
-3
0
3
dB
Frequency response
fG
b, c
b
V1
-3.0
-2.1
--
dB
Differential gain
DG
-- e a S -- -- -- -- --
3 3 --
5 5
% deg
Differential phase DP Allowable input amplitude VIN-AC
1.28 Vp-p
Noise
S/N
S: Input = 250kHz, 1.0Vp-p output (Vp-p) N: Input = DC ground output (mVrms)
f
a
V2 55 60 -- dB
d d
a a
V2 V3 V4 V5 V6 3.5 3.5 1.3 1.7 5.0 5.0 2.3 2.7 6.5 6.5 3.3 3.7 V V V V
VIN-AC Output DC voltage VAUTO-DC VFEED-DC 250kHz, 1.28Vp-p, VOUT-DC sine wave input
a
a
-3-
Electrical Characteristics Measuring Circuit
V4 SW1 0.01F 0.1F LPF Note 3) SW2 8 7 6 5 V1 V6 BPF Note 4) V2 0.1F 5.1k
V5
9V S Vector scope
a.
250kHz, 1.28Vp-p sine wave
b.
250kHz, 300mVp-p sine wave
c.
3.58MHz, 300mVp-p sine wave
d.
Ground
f. CXL5001M/P
250kHz, 1.0Vp-p sine wave
1M 100k
VSS
VCL
-4-
1 2 3 4 A2 A1 9V 0.01F CLK fCLK = 10.7MHz VCLK = 250mVp-p sine wave 5V
CLK VDD
VBIAS
AUTO
FEED OUT
e. V3
5-staircase wave
IN
a
b
CXL5001M/P
CXL5001M/P
Note 1) Frequency response measuring condition V3.58MHz (Output signal voltage [Vp-p] at 3.58MHz input) V250kHz (Output signal voltage [Vp-p] at 250kHz input) Set Pin 8 (IN) voltage [V] = VIN-DC + 640mV.
[V] 3.58MHz, 300mVp-p sine wave 250kHz, 300mVp-p sine wave 640mV (adjust with VBIAS) VIN-DC
Note 2) Differential gain and differential phase measuring condition
5-staircase wave signal Chroma 40 IRE 140 IRE (1.0Vp-p) 40 IRE 1H 63.5s
DG and DP are measured at output S point by vector scope.
Note 3) LPF frequency response
(Delay time [dB] 0 -3 140ns)
Note 4) BPF frequency response
[dB] 0 -3
-50 0 5.8 10.7 Frequency [MHz]
-50 0 50 200 4.1M 10.7M
Frequency [Hz]
-5-
CXL5001M/P
Application Circuit
9V
5.1k 0.01F 0.1F Composite video signal input 8 1M 7 6 5 2SA1175 CXL5001M/P 0.1F L. P. F 1H delay signal output Delay time = 140ns
1 0.01F 47F 0.01F 47F
2
3
4 0.01F CLK fCLK = 10.7MHz VCLK = 250mVp-p sine wave
5V
9V
Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same.
Example of Representative Characteristics
Frequency response vs. Ambient temperature
0 Input = 300mVp-p 3.58MHz, sine wave 0
Frequency response vs. Supply voltage
Input = 300mVp-p 3.58MHz, sine wave
fG - Frequency response [dB]
-1
fG - Frequency response [dB]
0 20 40 60 Ta - Ambient temperature [C]
-1
-2
-2
-3
-3
-4 -20
-4 4.7 5.0 5.3 VCL - Supply voltage [V]
Frequency response vs. Supply voltage
0 Input = 300mVp-p 3.58MHz, sine wave 1
Insertion gain vs. Ambient temperature
Input = 1.28Vp-p 250kHz, sine wave
fG - Frequency response [dB]
-1
IG - Insertion gain [dB]
9.0 VDD - Supply voltage [V] 9.5
0
-2
-1
-3
-2
-4 8.5
-3 -20 0 60 20 40 Ta - Ambient temperature [C]
-6-
CXL5001M/P
Insertion gain vs. Supply voltage
1 Input = 1.28Vp-p 250kHz, sine wave 1
Insertion gain vs. Supply voltage
Input = 1.28Vp-p 250kHz, sine wave
IG - Insertion gain [dB]
0
IG - Insertion gain [dB]
4.7 5.0 5.3 VCL - Supply voltage [V]
0
-1
-1
-2
-2
-3
-3 8.5 9.0 VDD - Supply voltage [V] 9.5
Differential gain vs. Ambient temperature
Differential gain vs. Supply voltage
DG - Differential gain [%]
DG - Differential gain [%]
0 20 40 60 Ta - Ambient temperature [C]
4
4
3
3
2
2
1
1
0 -20
0
4.7
5.0 5.3 VCL - Supply voltage [V]
Differential gain vs. Supply voltage
0 4 -1
Frequency response
DG - Differential gain [%]
Gain [dB]
3
-2 -3
2 -4 1 10k 100k Frequency [Hz] 1M
0 8.5
9.0 VDD - Supply voltage [V]
9.5
-7-
CXL5001M/P
Package Outline CXL5001M
Unit: mm
8PIN SOP (PLASTIC)
+ 0.4 6.1 - 0.1 + 0.4 1.85 - 0.15
8
5 0.15 + 0.2 0.1 - 0.05
+ 0.3 5.3 - 0.1
7.9 0.4
1 0.45 0.1
4 + 0.1 0.2 - 0.05 1.27
6.9
0.24 M
PACKAGE STRUCTURE
PACKAGE MATERIAL SONY CODE EIAJ CODE JEDEC CODE SOP-8P-L01 SOP008-P-0300 LEAD TREATMENT LEAD MATERIAL PACKAGE MASS EPOXY RESIN SOLDER PLATING 42/COPPER ALLOY 0.1g
CXL5001P
8PIN DIP (PLASTIC)
8
5
7.62
+ 0.3 6.4 - 0.1
+ 0.4 9.4 - 0.1
+ 0.1 0.05 0.25 -
0 to 15
EPOXY RESIN SOLDER PLATING COPPER ALLOY 0.5g
1 2.54
4
0.5 0.1 1.2 0.15
3.0 MIN
0.5 MIN
+ 0.4 3.7 - 0.1
PACKAGE STRUCTURE
PACKAGE MATERIAL SONY CODE EIAJ CODE JEDEC CODE DIP-8P-01 DIP008-P-0300 LEAD TREATMENT LEAD MATERIAL PACKAGE MASS
-8-
0.5 0.2

▲Up To Search▲

Price & Availability of CXL5001M

	To Download CXL5001M Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .